Hydraulic Product

The Fluid Level Gauge:

• Is available in two sizes – 3" and 5" between bolt centres
• Has a sturdy and low profile outer case
• Is ready for immediate installation; complete with gaskets and attaching bolts
• requires only two mounting holes for installation
• should be installed on a smooth and level surface
• has all external metal parts plated and, or powdered coated
• has a large and clear sight area providing high visibility
• is available with optional temperature gauge

 

Gauge Isolator Valve protects the pressure gauge from damage due to pressure surges, hydraulic shock and mechanical vibrations. The fluid is completely isolated from the gauge and connected directly to the gauge port as long as the knob is kept pressed thereby giving instant and accurate readings on the gauge. On release of the knob, the spring-loaded valve closes automatically to connect the gauge port to the tank by blocking the pressure port. An orifice in the gauge port acts as a partial snubber and protects the gauge from the initial surge of fluid when the knob is pressed.

The Single Station Gauge Isolator Valve:

• Has a 3000 PSI working pressure
• Comes with a guarantee of below 5cc/min. drain leakage in a new valve
• Can work between temperatures of -34.44° C (-30° F) and 115.56° C (240° F)
• Is made from a high grade investment casting body
• Requires minimum force to operate
• Has easy plumbing into the system
• Is tested 100% under rigid parameters
• Can be panel or line mounted
• Meets most operating conditions

Additional Information:

• Minimum Order Quantity: 10 Set

Suction Strainers are suitable for filtering hydraulic fluids, coolants, cutting fluids, lubricants and mineral oils and can function upto a maximum temperature of 90 deg C. They extend the life of the equipment and reduce breakdown by continuous filtering action, thereby protecting the pump and system components from damage due to clogging. The strainers can be reused after cleaning with petrol or similar fluids.

The Suction Strainers:

• Come in a range of flows from 15 LPM (3 GPM) to 450 LPM (100 GPM) and thread sizes of ½" BSP to 3" BSP
• Have a standard filtration of 149 microns
• Construction consists of a stainless steel filtering media, supported by inner plated perforated sheet and affixed wIth epoxy bonding material to plastic/aluminium alloy/sheet metal top and bottom caps

Filter Breathers are a combination unit for filtering air displacement to the reservoir and straining oil while filling. They are a must for hydraulic systems ensuring clean air passes into the reservoir, thus prolonging the life of the system components. When used as a crankcase ventilator, it helps to prolong the life of the engine oil and the oil filter. They are used in machine tool construction, mining, marine and agricultural equipments.
The Filter Breather Assembly:

Is available in Tank Top (TT) and Side Mounting (SM) options

Has displacement capacities of 250 LPM and 700 LPM

Has standard filtration of 40 microns

Displaces air from underneath the cap thereby improving performance

Is compatible with all fluids

Parts are powder coated and or made from high grade plastic ensuring non-corrosion

Has a Safety chain to prevent misplacement while filling oil or cleaning the filter

Is a ready to install package with fasteners and safety chain

Needs to be mounted on a flat and clean surface free of burrs to provide a good sealing surface

Related Product Categories

Plastic Filter Assembly

Filter Assemblies

Iron Polymaltose Complex

Iron Folic Acid Tablet

The Flexible Drive Coupling:

• Is available in five sizes to suit 1 HP to 75 HP
• Has crowned tooth form gears permitting axial and maximum angular misalignment of 1.5 degrees
• Is easy to assemble and require no maintenance or lubrication.
• Has superior material and can withstand wide operating temperatures and Severe load conditions
• Has no transmission noise

Single Pilot Check valve is used to lock a cylinder or part of a circuit and to prevent reverse flow until the pilot pressure is applied. The purpose of the check valve is to permit flow in one direction and block it in the opposite direction. In a free flow direction through the inlet, the ball is unseated and the flow is out of the cylinder port. When the control valve is centered, the load is locked. With pressure applied at the pilot piston, the ball is held open thereby allowing return flow. The mechanism is internally piloted. The directional valve cylinder ports should be connected to the tank in the centre condition.

The Single Pilot Check valve:

• Body is made of extruded aluminum alloy
• Has internal parts made of hardened steel
• Has a rated flow of 30 LPM
• Functions with a working pressure of 210 kg/cm3
• Has a damped pilot piston to reduce damaging shocks
• Comes with easily replaceable seats in some models

 

Double Pilot Check valve is used to lock a cylinder or part of a circuit and to prevent reverse flow until the pilot pressure is applied. The purpose of the check valve is to permit flow in one direction and block it in the opposite direction. In a free flow direction through the inlet, the ball is unseated and the flow is out of the cylinder port. When the control valve is centered, the load is locked. With pressure applied at the pilot piston, the ball is held open thereby allowing return flow. The mechanism is internally piloted. The directional valve cylinder ports should be connected to the tank in the centre condition.

 

The Double Pilot Check valve:

 

• Body is made of extruded aluminium alloy
• Has internal parts made of hardened steel
• Has a rated flow of 30 LPM
• Functions with a working pressure of 210 kg/cm³
• Has a damped pilot piston to reduce damaging shocks
• Comes with easily replaceable seats in some models

 

Pressure Line Filter is ideal for application in simple hydraulic systems. It provides reliable protection to dirt sensitive parts.

The Pressure Line Filter:

 

• Is available in 10 micron, 25 micron and 75 micron ratings
• Has a maximum working pressure of 140 bar
• Has a flow rate of 20 LPM
• Uses sintered bronze filter cartridges to provide absolute filtration
• Is made from high grade castings and has nitrite rubber sealing

Return Line Filter is intended for direct mounting on the hydraulic reservoir in mobile installations as well as stationary applications like machine tools, plastic machinery, etc.

The Return Line Filter:

• Is available in 6 sizes with port sizes of ½" BSP, ¾" BSP, 1" BSP, 1 ¼" BSP and 1 ½" BSP for flows up to 450 LPM
• Has filtration options of 10 microns and 25 microns in each size
• Can withstand maximum pressure of Bar
• Comes with an optional visual clogging indicator
• Contains a magnet built in to arrest ferrous particles in the system
• Has a by-pass check valve to handle excess pressure due to clogging
• Allows easy replacement of the filter cartridge without disturbing the plumbing
• Requires one inlet fitting and discharges directly into the reservoir
• Has an outlet suitable for hose connection thereby reducing the installation cost

 

Threaded Breather is a unit for filtering air displacement to the reservoir. It is to be fixed on hydraulic or lubrication oil reservoirs in applications such as machine tools, mobile equipment and industrial machinery.

 

The Threaded Breather:

• Threaded Breather displacement capacities of 25 LPM and 700 LPM
• Has a standard filtration of 40 microns
• Is available in a large variety of thread sizes
• Displaces air from underneath the cap thereby improving performance
• All parts are plated and or powder coated for corrosion resistance